| Peer-Reviewed

Characterization of Electrochemical Cycling-Induced New Products of NaCuO2 Cathode Material for Sodium Secondary Batteries

Received: 17 September 2014     Accepted: 5 October 2014     Published: 30 October 2014
Views:       Downloads:
Abstract

Using a Na/NaCuO2 cell, we investigate the conversion of NaCuO2 during charge and discharge reactions and the new products formed by the conversion. In the voltage range of 0.75 to 3.0 V, the results of ex-situ XRD analysis indicate that Na2CuO2, an unstable amorphous discharge product, converted into CuO and Cu2O. Moreover, an XPS analysis reveals Na2O is formed on the surface of a NaCuO2 electrode. From 1.7 to 4.2 V, on the other hand, the first charge product, Na1-xCuO2, should partially form CuO. This behavior is similar to the reaction in which the charge of a Li/LiCuO2 cell forms CuO. Then, after the discharge, CuO and Cu2O are observed as the main components in XRD patterns of the electrode. NaCuO2 phase appeared again after the subsequent charge. NaCuO2 is gradually converted into CuO as the main component as the cycles proceed. The cycling-induced new products of NaCuO2 change, depends on the voltage ranges.

Published in American Journal of Physical Chemistry (Volume 3, Issue 5)
DOI 10.11648/j.ajpc.20140305.12
Page(s) 61-66
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2014. Published by Science Publishing Group

Keywords

XRD Analysis, Sodium Copper Oxide, Metal Oxide Cathode, Sodium-Ion Batteries

References
[1] R. Berthelot, D. Carlier and C. Delmas, “Electrochemical investigation of the P2–NaxCoO2 phase diagram,” Nat. Mater., 2011, 74, pp. 74–80.
[2] S. Komaba, C. Takei, T. Nakayama, A. Ogata and N. Yabuuchi, “Electrochemical intercalation activity of layered NaCrO2 vs. LiCrO2,” Electrochem. Commun. 2010, 12, pp. 355–358.
[3] X. Xia and J.R. Dahn, “NaCrO2 is a fundamentally safe positive electrode material for sodium-ion batteries with liquid electrolytes,” Electrochem. Solid State Lett., 2012, 15(1), A1–A4.
[4] X. Ma, H.Chen and G. Ceder, “Electrochemical properties of monoclinic NaMnO2,” J. Electrochem. Soc., 2011, 158, A1307–A1312.
[5] R. Stoyanova, D. Carlier, M. Sendova-Vassileva, M. Yoncheva, E. Zhecheva, D. Nihtianova and C. Delmas, “Stabilization of over-stoichiometric Mn4+ in layered Na2/3MnO2,” J. Solid State Chem., 2010, 183, pp. 1372–1379.
[6] H. Kim, D.J. Kim, D.H. Seo, M.S. Yeom, K. Kang, D.K. Kim and Y. Jung, “Ab initio study of the sodium intercalation and intermediate phases in Na0.44MnO2 for sodium-ion battery,” Chem. Mater., 2012, 24, pp. 1205–1211.
[7] S. Komaba, T. Nakayama, A. Ogata, T. Shimizu, C. Takei, S. Takada, A. Hokura and I. Nakai, “Electrochemically reversible sodium intercalation of layered NaNi0.5Mn0.5O2 and NaCrO2,” ECS Trans., 2008, 16 (42), pp. 43–55.
[8] Y. Ono, Y. Yui, M. Hayashi, K. Asakura, H. Kitabayashi, K. I. Takahashi, “Electrochemical properties of NaCuO2 for sodium-ion secondary batteries,” ECS Trans., 2014, 58 (12), pp. 33–39.
[9] H. Arai, S. Okada, Y. Sakurai and J. Yamaki, “Electrochemical and structural study of Li2CuO2, LiCuO2 and NaCuO2,” Solid State Ion., 1998, 106, pp. 45–53.
[10] N.E. Brase, M. O’Keeffe, R.B. von Dreele,V.G. Young Jr., “Crystal structures of NaCuO2 and KCuO2 by neutron diffraction,” J. Solid State Chem., 1989, 83, pp. 1–7.
[11] A. Barrie and F.J. Street, “An Auger and X-ray photoelectron spectroscopic study of sodium metal and sodium oxide,” J. Electron Spectrosc. Relat. Phenom., 1977, 7, pp. 1–30.
[12] Y. Arachi, T. Setsu, T. Ide, K. Hinoshita and Y. Nakata, “Reversible electrochemical reaction of CuO with Li in the LiCuO2 system,” Solid State Ionics, 2012, 225, 611–614.
[13] E. A. Reakelboom, A.L. Hector, M.T. Weller and J.R. Owen, “Electrochemical properties and structures of the mixed-valence lithium cuprates Li3Cu2O4 and Li2NaCu2O4,” Journal of Power Source, 2011, 97–98, pp. 465–468.
[14] Y. Arachi, Y. Nakata, K. Hinoshita, and T. Setsu, “Changes in electronic structure of Li2−xCuO2,” Journal of Power Sources, 2011, 196, pp. 6939–6942.
Cite This Article
  • APA Style

    Yoko Ono, Yuhki Yui, Kaoru Asakura, Jiro Nakamura, Masahiko Hayashi, et al. (2014). Characterization of Electrochemical Cycling-Induced New Products of NaCuO2 Cathode Material for Sodium Secondary Batteries. American Journal of Physical Chemistry, 3(5), 61-66. https://doi.org/10.11648/j.ajpc.20140305.12

    Copy | Download

    ACS Style

    Yoko Ono; Yuhki Yui; Kaoru Asakura; Jiro Nakamura; Masahiko Hayashi, et al. Characterization of Electrochemical Cycling-Induced New Products of NaCuO2 Cathode Material for Sodium Secondary Batteries. Am. J. Phys. Chem. 2014, 3(5), 61-66. doi: 10.11648/j.ajpc.20140305.12

    Copy | Download

    AMA Style

    Yoko Ono, Yuhki Yui, Kaoru Asakura, Jiro Nakamura, Masahiko Hayashi, et al. Characterization of Electrochemical Cycling-Induced New Products of NaCuO2 Cathode Material for Sodium Secondary Batteries. Am J Phys Chem. 2014;3(5):61-66. doi: 10.11648/j.ajpc.20140305.12

    Copy | Download

  • @article{10.11648/j.ajpc.20140305.12,
      author = {Yoko Ono and Yuhki Yui and Kaoru Asakura and Jiro Nakamura and Masahiko Hayashi and Kazue Ichino Takahashi},
      title = {Characterization of Electrochemical Cycling-Induced New Products of NaCuO2 Cathode Material for Sodium Secondary Batteries},
      journal = {American Journal of Physical Chemistry},
      volume = {3},
      number = {5},
      pages = {61-66},
      doi = {10.11648/j.ajpc.20140305.12},
      url = {https://doi.org/10.11648/j.ajpc.20140305.12},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajpc.20140305.12},
      abstract = {Using a Na/NaCuO2 cell, we investigate the conversion of NaCuO2 during charge and discharge reactions and the new products formed by the conversion. In the voltage range of 0.75 to 3.0 V, the results of ex-situ XRD analysis indicate that Na2CuO2, an unstable amorphous discharge product, converted into CuO and Cu2O. Moreover, an XPS analysis reveals Na2O is formed on the surface of a NaCuO2 electrode. From 1.7 to 4.2 V, on the other hand, the first charge product, Na1-xCuO2, should partially form CuO. This behavior is similar to the reaction in which the charge of a Li/LiCuO2 cell forms CuO. Then, after the discharge, CuO and Cu2O are observed as the main components in XRD patterns of the electrode. NaCuO2 phase appeared again after the subsequent charge. NaCuO2 is gradually converted into CuO as the main component as the cycles proceed. The cycling-induced new products of NaCuO2 change, depends on the voltage ranges.},
     year = {2014}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Characterization of Electrochemical Cycling-Induced New Products of NaCuO2 Cathode Material for Sodium Secondary Batteries
    AU  - Yoko Ono
    AU  - Yuhki Yui
    AU  - Kaoru Asakura
    AU  - Jiro Nakamura
    AU  - Masahiko Hayashi
    AU  - Kazue Ichino Takahashi
    Y1  - 2014/10/30
    PY  - 2014
    N1  - https://doi.org/10.11648/j.ajpc.20140305.12
    DO  - 10.11648/j.ajpc.20140305.12
    T2  - American Journal of Physical Chemistry
    JF  - American Journal of Physical Chemistry
    JO  - American Journal of Physical Chemistry
    SP  - 61
    EP  - 66
    PB  - Science Publishing Group
    SN  - 2327-2449
    UR  - https://doi.org/10.11648/j.ajpc.20140305.12
    AB  - Using a Na/NaCuO2 cell, we investigate the conversion of NaCuO2 during charge and discharge reactions and the new products formed by the conversion. In the voltage range of 0.75 to 3.0 V, the results of ex-situ XRD analysis indicate that Na2CuO2, an unstable amorphous discharge product, converted into CuO and Cu2O. Moreover, an XPS analysis reveals Na2O is formed on the surface of a NaCuO2 electrode. From 1.7 to 4.2 V, on the other hand, the first charge product, Na1-xCuO2, should partially form CuO. This behavior is similar to the reaction in which the charge of a Li/LiCuO2 cell forms CuO. Then, after the discharge, CuO and Cu2O are observed as the main components in XRD patterns of the electrode. NaCuO2 phase appeared again after the subsequent charge. NaCuO2 is gradually converted into CuO as the main component as the cycles proceed. The cycling-induced new products of NaCuO2 change, depends on the voltage ranges.
    VL  - 3
    IS  - 5
    ER  - 

    Copy | Download

Author Information
  • Energy and Environment Systems Laboratories, NTT Corporation, Kanagawa 243-0198, Japan

  • Energy and Environment Systems Laboratories, NTT Corporation, Kanagawa 243-0198, Japan

  • Energy and Environment Systems Laboratories, NTT Corporation, Kanagawa 243-0198, Japan

  • Energy and Environment Systems Laboratories, NTT Corporation, Kanagawa 243-0198, Japan

  • Energy and Environment Systems Laboratories, NTT Corporation, Kanagawa 243-0198, Japan

  • Energy and Environment Systems Laboratories, NTT Corporation, Kanagawa 243-0198, Japan

  • Sections